9999 in stock

 

The smallest member of Meyer's MILO line array family, this speaker's extremely high power-to-size ratio results in exceptional fidelity and transient response for intelligibility and high impact.Just over a foot and a half long and weighing only 41.2 lbs yet capable of producing up to 128 dB SPL over its wide and even 100-degree horizontal coverage area, MINA will find a place in a variety of applications. Its small footprint makes it an ideal curvilinear array system for low-profile, high-fidelity sound reinforcement, as well as hotel ballrooms, frontfill and under-balcony applications.Mina integrates seamlessly with M'elodie and MICA, and also pairs nicely with Meyer's 500-HP subwoofers; flexible mounting options such as QuickFly rigging with captive GuideALinks simplify use in flown or groundstacked arrays.

Acoustical
Operating Frequency Range: 66 Hz – 18 kHz
Note: Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics.
Frequency Response: 70 Hz – 17.5 kHz ±4 dB
Note: Measured free field with 1/3 octave frequency resolution at 4 meters.
Phase Response: 1 kHz to 18 kHz ±30°
Maximum Peak SPL: 128 dB
Note: Measured with music referred to 1 meter.
Dynamic Range: >110 dB
Horizontal Coverage: 100°
Vertical Coverage: Varies, depending on array length and configuration
Crossover: 760 Hz
Note: At this frequency, the transducers produce equal sound pressure levels.

Transducers
Low and Low-Mid Frequency: Two 6.5” cone drivers with neodymium magnets
Nominal impedance: 4Ω
Voice coil size: 1.5”
High Frequency: One 3” compression driver
Nominal impedance: 8Ω
Voice coil size: 3”
Diaphragm size: 3”
Exit size: 1.2”

Audio Input
Type: Differential, electronically balanced
Maximum Common Mode Range: ±5 V DC
Connectors: XLR female input with XLR male loop output
Input Impedance: 10 kΩ differential between pins 2 and 3
Wiring
Pin 1: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
Pin 2: Signal +
Pin 3: Signal –
Case: Earth ground and chassis
DC Blocking: Differential DC blocking up to maximum common mode voltage
CMRR: >50 dB, typically 80 dB (50 Hz – 500 Hz)
RF Filter
Common mode: 425 kHz
Differential mode: 142 kHz
TIM Filter: <80 kHz, integral to signal processing
Nominal Input Sensitivity: 0 dBV (1.0 V rms, 1.4 V peak) continuous average is typically the onset of limiting for noise and music
Input Level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.

Amplifier
Type: Three-channel, Class-D
Output Power: 975 W total (three channels; 2 x 375 W, 1 x 225 W)
Note: Wattage rating based on the maximum unclipped burst sine-wave rms voltage the
amplifier will produce into the nominal load impedance: 39 V rms low channels, 43 V rms high channel.
Total Output: 1950 W peak
Note: Peak power based on the maximum unclipped peak voltage the amplifier will produce for at least 100 milliseconds into the nominal load impedance: 55 V peak low channels, 60 V peak high channel.
THD, IM TIM: <.02%
Load Capacity: 4 Ω low channels, 8 Ω high channel
Cooling: Convection

Power
Connectors: PowerCon with loop output
Voltage Selection: Automatic, continuous from 90–265 V AC
Safety Agency Rated Operating Voltage: 100–240 V AC, 50/60 Hz
Turn On/Turn Off Points
90 V AC turn-on, no turn-off
Internal fuse-protection above 265 V AC

Current Draw
Idle Current: 0.256 A rms (115 V AC); 0.249 A rms (230 V AC); 0.284 A rms (100 V AC)
Maximum Long-Term Continuous Current: 1.26 A rms (115 V AC); 0.66 A rms (230 V AC); 1.50 A rms (100 V AC)
Burst Current: 3.24 A rms (115 V AC); 1.74 A rms (230 V AC); 4.02 A rms (100 V AC)
Note: AC power cabling must be of sufficient gauge so that under burst current rms conditions, cable transmission losses do not cause the loudspeaker’s voltage to drop below the specified operating range.
Ultimate Short-Term Peak Current: 10.4 A peak (115 V AC); 5.2 A peak (230 V AC); 11.1 A peak (100 V AC)
Inrush Current 16.8 A peak (115 V AC); 20.0 A peak (230 V AC); 15.0 A peak (100 V AC)
Note: Current draw for a single loudspeaker. Loop output not used.

Physical
Dimensions: 20.27"W x 8.38"H x 15.32"D (515 x 213 x 389 mm) with rigging pins
Weight: 41.2 lbs (18.69 kg)
Enclosure: Premium birch plywood
Finish: Black textured
Protective Grille: Powder-coated, hex-stamped steel with black mesh
Rigging
End frames with four captive GuideALinks, secured with 0.25" x 0.53" quick-release pins;
Metric M6 attachment points for optional MYA.MINA mounting yoke and MUB.MINA Ubracket

Environmental
Temperature
Operating: 32°F to 113°F (0°C to +45°C)
Non-Operating: -40°F to 167°F (–40°C to +75°C)
Humidity: To 95% at 77°F (35°C)
Operating Altitude: To 15,000 ft (4600 m)
Shock: 30 g 11 msec half-sine on each of 6 sides
Vibration: 10 Hz – 55 Hz (0.010 m peak-to-peak excursion)