9999 in stock

Meyer 700-HP SUB Ultra High Power Subwoofer Using Ultra-efficient neodymium magnet drivers, this speaker offers extremely low distortion for ultimate low-frequency clarity, along with very high peak power that yields excellent transient reproduction.Besides being stackable, it is flyable using an optional rigging kit, and is also transportable in blocks using an optional heavy duty caster frame.

The 700-HP subwoofer is ideal for stadiums, arenas and concert halls, medium-to-large theatres and clubs, theme parks and cinema.

Operating Frequency Range1: 28 Hz - 150 Hz
Free Field Frequency Response2: 30 Hz - 125 Hz ±4 dB
Phase Response: 45 Hz - 145 Hz ±30°
Maximum Peak SPL3: 139 dB
Dynamic Range: >110 dB

360° (single unit); varies with number of units and configuration

Low Frequency: Two 18" cone drivers
Nominal impedance: 4Ω
Voice coil size: 4"
Power-handling capability: 1200 W (AES)4

Audio Input     
Type: Differential, electronically balanced
Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
Connectors: Female XLR input with male XLR loop output or VEAM all-in-one (integrates AC, audio and network)
Input Impedance: 10 kΩ differential between pins 2 and 3
Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
Pin 2: Signal +
Pin 3: Signal -
Case: Earth ground and chassis
DC Blocking: None on input, DC blocked through signal processing
CMRR: >50 dB, typically 80 dB (50 Hz–500 Hz)
RF Filter
Common mode: 425 kHz
Differential mode: 142 kHz
TIM Filter: Integral to signal processing (<80 kHz)
Nominal Input Sensitivity: 0 dBV (1 V rms, 1.4 V pk) continuous is typically the onset of limiting for noise and music
Input Level: Audio source must be capable of producing a minimum of +20 dBV (10  V rms, 14 V pk) into 600Ω in order to produce maximum peak SPL over the operating bandwidth of the loudspeaker.

Type: Two-channel complementary power MOSFET output stages (class AB/H)
Output Power: 2250 W (1125 W/channel)5
THD, IM, TIM: <.02%
Load Capacity: 4Ω each channel
Cooling: Forced air cooling, two fans (one ultrahigh-speed reserve fan)

AC Power   
Connector: 250 VAC NEMA L6-20 (twist lock), IEC 309 male inlet, or VEAM
Automatic Voltage Selection: Automatic, two ranges, each with high-low voltage tap
Safety Agency Rated Operating Range: 95 VAC – 125 VAC, 208 VAC - 235 VAC; 50/60 Hz
Turn-on and Turn-off Points: 85 VAC - 134 VAC; 165 VAC - 264 VAC; 50/60 Hz
Current Draw
Idle Current: 0.640 A rms at 115 VAC; 0.320 A rms at 230 VAC; 0.850 A rms at 100 VAC
Max Long-Term Continuous Current (>10 sec): 8.8 A rms at 115 VAC; 4 A rms at 230 VAC; 10 A rms at 100 VAC
Burst Current (<1 sec): 19 A rms at 115 VAC; 9.5 A rms at 230 VAC; 22 A rms at 100 VAC
Ultimate Short-Term Peak Current Draw: 39 A pk at 115 VAC; 20 A pk at 230 VAC; 45 A pk at 100 VAC
Inrush Current: 7 A pk at 115 VAC; 7 A pk at 230 VAC; 10 A pk at 100 VAC

Dimensions: 45.93"W x 22.50"H x 30.00"D (1167 x 572 x 762 mm)
Dimensions with rigging: 50.58"W x 22.50"H x 30.00"D (1285 x 572 x 762 mm)
Weight: 204 lbs (92.53 kg)
Weight with rigging: 259 lbs (117.48 kg)
Enclosure: Multi-ply hardwood
Finish: Black textured
Protective Grille: Perforated metal grille lined with acoustical black mesh
Rigging: Optional QuickFly® rigging kit available, with aluminum and steel side rigging bars, AlignaLinks and quick release pins

RMS Network (Optional) 
Equipped for two conductor twisted-pair network, reporting all operating parameters of amplifiers to system operator’s host computer.

1. Recommended maximum operating frequency range. Response depends upon loading conditions and room acoustics.
2. Measured with 1/3 octave frequency resolution at 4 meters.
3. Measured with music at 1 meter.
4. Power handling is measured under AES standard conditions: transducer driven continuously for two hours with a band-limited noise signal having a 6 dB peak-to-average ratio.
5. Amplifier wattage rating is based on the maximum unclipped burst sine-wave rms voltage the amplifier will produce into the nominal load impedance. Both channels 67 V rms (95 V pk) into 4 ohms.